The primary driver for initial efforts in high temperature flange design came from improvements in the steam power generation industry that resulted in higher steam temperatures and pressures being used in the late 1920s and early 1930s. The initial work of Baumann [3] in 1930 looked at the creep of bolts and flange components of […]
ASME STP-PT-036:2010 pdf download Read More »
This guideline explains the current use and application of data analytics and data science in the oil and gas industry. It is designed to provide guidance on how to utilize data analytics and machine learning/artificial intelligence (ML/AI) to address a given business need, resulting in value-creation. Within the guidelines will be descriptions of various data
ASME STB-1:2020 pdf download Read More »
1.1 This specification covers seamless tubes of nickel and nickel alloys, as shown in Table 1, for use in condenser and heat-exchanger service. 1.2 This specification covers outside diameterand aver-age wall, or outside diameter and minimum wall tube. 1.2.1 The sizes covered by this specification are 3 in.(76.2 mm) and under in outside diameter with
ASME SB 163:2015 pdf download Read More »
1.1 This specification covers aluminum-alloy sand castings designated as shown in Table 1. 1.2 This specification is not intended for aluminum-alloy sand castings used in aerospace applications. 1.3 Alloy and temper designations are in accordance with ANSI H35.1/H35.1M. Unified Numbering System alloy des-ignations are in accordance with Practice E527. 1.4 Unless the order specifies the
ASME SB 26:2019 pdf download Read More »
1.1 This peicaion covers grades of nominal wall thick-ness, stainless steel tubing for services requiring general corrosion resisiance, with particular emphasis on resistance 1o stress corrosion cncking. These steels are susceptible to embritlement if used for prolonged peniods a elevated tem-peratures. 1.2 The values stated in either SI units or inch-pound units are to be
ASME SA 789:2017 pdf download Read More »
1.1 This specification covers forged carbon steel piping components intended primarily for service in pressure pip-ing systems from −20 to +650 °F [−30 to +345 °C] where inherentnotch toughness is desired, butwhere notch tough-ness testing is not required. Included are forged or ring-rolled flanges, forged fittings, and valves made to specified dimensions, orto dimensional standards
ASME SA-727-SA-727M:2021 pdf download Read More »
1.1 This specification covers minimum-wall-thickness, electric-resistance-welded, carbon steel tubes including thosebent, ifspecified, into theformofU-tubes forapplica-tion in tubular feedwater heaters. 1.2 The tubing sizes covered shall be 1 ⁄ 8 to 1 1 ⁄ 4 in.[15.9 to 31.8 mm] outside diameter, inclusive, and wall thicknesses equal to or greater than 0.045 in. [1.1 mm].
ASME SA-557-SA-557M:2021 pdf download Read More »
1.1 This specification covers carbon steel plates intended primarily for service in welded pressure vessels where im-proved notch toughness is important.
ASME SA 516:2019 pdf download Read More »
1.1 This specification covers hot- and cold-finished bars of stainless steel, including rounds, squares, and hexagons, and hot-rolled or extruded shapes such as angles, tees, and channels for use in boiler and pressure vessel construction. 2 N OTE 1—There are standards covering high nickel, chromium, auste-nitic corrosion, and heat-resisting alloy materials. These standards are under
ASME SA 479:2019 pdf download Read More »
1.1 This specification covers austenitic alloy steel pipe for use in high-temperature, corrosive, or nuclear pressure service. 1.2 Several grades ofaustenitic stainless steel are covered as indicated in Table 1. 1.3 Optional supplementary requirements are provided when additional testing may be required.
ASME SA-451-SA-451M:2021 pdf download Read More »