This Standard covers plumbing fttings, including the following: (a) anti-siphon fill valves; (b) automatic compensating valves other than those for individual wall-mounted showering systems; (C) flushometer valves and solenoid valves; (d) supply line stops; (e) temperature-actuated in-line mixing valves; (f) thermal expansion relief valves; and (g) trap primers.
CSA B125.3-12 pdf download Read More »
This Standard covers plumbing supply fittings and accessories located between the supply stop and the terminal fitting, inclusive, as follows: (a) automatic compensating valves for individual wall-mounted showering systems; (b) bath and shower supply fittings; (c) bidet supply fittings; (d) clothes washer supply fittings; (e) drinking fountain supply fittings; (f) humidifier supply stops; (g) kitchen,
CSA B125.1-12 (R2017) pdf download Read More »
This Standard covers the protection from lightning of a) recreational, residential, institutional, medical, agricultural, industrial, commercial, military, and telecommunications buildings and structures; b) tall, slender structures such as smokestacks, silos, tanks, towers, masts, and poles; c) immobile property such as equipment, tents, fences, trees, and solar arrays; and d) high-risk structures with dangerous contents such
CSA B72:20 pdf download Read More »
This Standard covers cast iron soil pipe, fittings, and means of joining for installation in gravity-flow plumbing systems inside and outside of buildings, above and below grade. Note: Pipe and fittings that com ply with this Standard are not universally com patible with pipe and fittings m anufactured in accordance with ASTM A74 and ASTM
CSA B70-12 (R2016) pdf download Read More »
The purpose of this Standard is to minimize the risk of personal injury by providing minimum requirements for the design, construction, installation, inspection, and maintenance of the mechanical refrigeration systems specified in Clauses 1.2.1 and 1.2.2. Note: This Standard does not directly address protection of property and preservation of the environment.
CSA B52-05 (R2009) pdf download Read More »
Except as indicated in Clause 1.2, Part 1 of this Standard applies to all boilers, pressure vessels, pressure piping, and fttings, as provided for by the Act (as defined in Clause 3) and identified in Part 1 of this Standard. Notes: 1) It is possible that the size limitations specified in provinciol or territorial statutes
CSA B51:19 pdf download Read More »
This Standard specifies general requirements, test methods, and markings for whirlpool and air-jetted bathtubs and suction fttings used in hydromassage bathtub systems that incorporate a bathtub and circulation pump. The circulation pump can be with or without (a) a piping system; and (b) induction of air (which can be achieved by integral suction or through
CSA B45.10-12 (R2017) pdf download Read More »
This Standard covers self-contained, recirculating, chemically controlled toilets and specifies requirements for (a) design; (b) materials; (c) components; (d) construction and finish; (e) testing; (f) installation; (g) operation; and (h) markings.
CSA B45.7-11 (R2016) pdf download Read More »
This Standard covers nonrecirculating toilets, vacuum toilets, and waste-holding tanks. For these products,this Standard specifies requirements for (a) design; (b) materials; (c) components; (d) construction and finish; (e) testing; (f) installation; (g) operation; and (h) markings.
CSA B45.6-11 (R2016) pdf download Read More »
ASME A17.8/CSA B44.8 applies to elevators permanently installed in a wind turbine tower to provide vertical transportation of authorized personnel and their tools and equipment only. Such elevators are typically subjected to extreme temperatures, humidity variations, and substantial horizontal motions where, by reason of their limited use and the types of construction of the structures
CSA B44.8-16 pdf download Read More »