Welcome to this website, where you can query the price of ASME standards, the latest version of ASME standards and the basic introduction of ASME standards.
The scope of this Standard is the standardization of safety and performance requirements for portable auto-motive service equipment(PASE) including, butnotlim-ited to, the following: (a) attachments, adapters, and accessories (b) hydraulic hand jacks (c) transmission jacks (d) engine stands (e) vehicle support stands (f) emergency tire-changing jacks (g) mobile lifts (h) service jacks (i) wheel dollies […]
ASME PASE:2014 pdf download Read More »
The scope of this Standard is the standardization of safety and performance requirements for portable auto-motive lifting equipment including: (a) hydraulic hand jacks (b) transmission jacks (c) engine stands (d) vehicle support stands (e) mechanical screw jacks (f) mechanical bumper jacks (g) scissors jacks (h) mechanical frame jacks (i) upright-type mobile lifts (j) service jacks
ASME PALD:2003 pdf download Read More »
SectionIST establishes the requirements for preservice and inservice testing and examination of certain compo-nents to assess their operational readiness in light-water reactor nuclear power plants. It identifies the compo- nents subject to test or examination, responsibilities,methods, intervals, parameters to be measured and eval-uated, criteria for evaluating the results, corrective action, personnel qualification, and record keeping.These
ASME OMA CODE:2011 pdf download Read More »
One unique aspect of the behavior of graphite is the material’s temperature response. Graphite, unlike other materials, increases in strength with increasing temperature. Tensile strength increases of ~50% are typical,with the strength increasing with temperature until the onset of plasticity at approximately 2000°C. This behavior requires the exclusion of oxidizing gases, such as air, to
ASME NTB-4:2021 pdf download Read More »
Appendix T in NH [7] provides three expressions for determining strain range [8] using elastic analysis and, if these rules cannot be satisfied, additional rules are provided,presumably less conservative, based on the results of inelastic analyses which require detailed constitutive models of material behavior under time varying loading conditions.For the CRBR, these behavioral models were
ASME NTB-3:2020 pdf download Read More »
Section 17.4.4.3.9.3, Consideration for Elastic Follow-up, provides a fairly extensive discussion of what constitutes elastic follow-up, where it is considered in the current rules, and guidance on how to implement that consideration. Also addressed is the background for the provisions for pressure-induced discontinuity stresses in the HBB-T-1330 rules for strain limits and the HBB-T-1430 rules
ASME NTB-2:2019 pdf download Read More »
This Section describes the evolution of nuclear qualty assurance from early quality control and inspection re-quirements for AEC nuclear weapons production and naval reactors programs; to the more comprehensive quality assurance program requirements for nuclear weapons production and AEC/DOE reactor development and technology activities; to the series of DOE quality assurance directives.
ASME NQA.TR:2020 pdf download Read More »
Movement of loads covered by this Standard shall be in accordance with the Standard’s requirements but not necessarily with its recommendations. The word “shall” is used to denote a requirement, the word “should” is used to denote a recommendation, and the word “may” is used to denote permission, which is neither a requirement nor a
ASME NML-1:2019 pdf download Read More »
This Standard covers requirements for the design,construction, and qualification and acceptance testing of the air-cleaning units and components which make up Engineered Safety Feature (ESF) and other high effi-ciency air and gas treatment systems used in nuclear power plants.
ASME N509:2002 pdf download Read More »
This Standard establishes common terminology and provides guidelines for the quality. description, princ-ple of operation, selection, operation, installation, and flow calibration of capillary tube thermal mass flow-meters and mass flow controllers for the measurement and control of the mass flow rate of gases. The content of this Standard applies to single-phase flows of pure gases
ASME MFC-21.1:2015 pdf download Read More »